It is very light and strong and designed to be assembled easily with a minimum amount of basic tools. The Crypto Monster case will accommodate all ATX form factor components.
You can use any ATX, Micro ATX or extended ATX motherboards, any 2,5 hard disks or SSD drives, any power supplies, 140 mm or 120 mm case fans and up to 7 graphic cards. Last but not least, it is stackable. Here are the key features: - ATX or Micro ATX motherboard mounts (brass posts and screws included). Extended ATX motherboards will also fit.
You can install 1 or 2 power supplies of any length. The power supplies can be rotated 180 degrees thanks to our mirrored screw pattern (this way the PSU intake fan can be facing outwards for cooler air) - High flow 140 mm fans can be used for excellent cooling but you can also use 120 mm fans. On the lower level 2 fans can be installed to cool the motherboard, CPU, hard disk and 7. On the upper level you can mount 3 fans to cool the graphic cards.
Our tests have shown a substantial drop in GPU temperature with the fans installed but keep in mind that the amount of cooling is entirely dependent on your own local conditions, the type of fans and the graphic cards used. Adjustable sliding bar can adapt to any length (or combination of) graphic cards, a real plus! - lots of cutouts available for cable ties for clean routing of cables. Very helpful to reduce cable clutter that can impair airflow.
There are 3 spots pre-drilled for standard 2,5 hard disks or SSD drives. This allows you to mount your drive in the best possible position according to your motherboard layout and accessories used.All screws and special hardware necessary are included. It is a win-win situation and rest assured that our detailed instructions will make assembly of this unit a breeze!
- Another advantage is that the Crypto Monster allows you to upgrade at any time. The case fans are not an absolute necessity and as can be seen on the pictures the mounting pattern of the fans is designed to let air flow naturally when no fans are installed. We recommend the use of high quality PCI risers, try to avoid the ones that have a Sata to Molex power cable because the yellow wire overheats and shorts out internally leading to card failure!
Make sure the USB cables that come with the PCI risers are 50 to 60 cm long (19.7 to 23.6 inches). The Crypto Monster case takes a lot of headaches away from the mining experience because everything fits like it should so you don't have to spend time drilling and cutting.
We went thru all the major headaches of trying to figure out what works and what doesn't so if you really think about it, the Crypto Monster is very reasonably priced and represents only a small percentage of the overall cost of a rig.. Recommended (but not included) accessories.On/OFF/Reset switch: very convenient to start or reboot the machine, much better than using a paper clip! Extremely useful, inexpensive and easy to install. There are essentially 2 units available: a transistor and a relay version, both work fine, it is only a matter of personal preference. All Crypto Monster cases have the holes pre-drilled in 2 different spots to accommodate both versions of the second PSU switch. The Crypto Monster Deluxe comes with these 2 accessories and necessary hardware. Width: 51,0 cm (20 inches) - Depth: 36,0 cm (14 inches) - Height: 37,5 cm (14,7 inches). It takes around 15 minutes and all you need is a couple of Philips screwdrivers. You get all necessary hardware necessary to assemble the case, motherboard and hard disk/SSD. The unit is stackable, just make sure you have enough air flowing to keep things cool...
The item "6, 7 GPU, crypto mining rig frame, aluminum case, Crypto Monster" is in sale since Friday, December 2, 2016. This item is in the category "Computers/Tablets & Networking\Computer Components & Parts\Computer Cases & Accessories\Computer Cases".The seller is "werewolfpat" and is located in Prague. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia.